Topic PostsLMS-forum
 

Not logged in


Recover Lost Password | Register     

     Printable Version | Subscribe | Add to Favourites

     Body Talk: Making a Silicon mold (1/24 Snakebite continued)
  Post new thread Poll:  
tamar





Posts: 804
Registered: 5-1-1989
Location: Gouda
Member Is Offline
Mood: A new beginning ;)
posted on 6-12-2004 at 15:16 Reply With Quote
Making a Silicon mold (1/24 Snakebite continued)



http://www.slotracinglemans.com/images/rfh/viper_mal01.jpg
Making a silicon mold is actually a quite easy, be it a little bit messy job.
For the average 1/24 GT you'll need ± 500gr of silicon, 25gr hardner, some sheetplastic, tamiya putty or miliput and some mdf to make a box to pour the silicon in.
Oh... and some Maskol, very handy stuff!

http://www.slotracinglemans.com/images/rfh/viper_mal02.jpg
As the master will be completely submerged in the silicon you need the Sheetplastic to close all openings in the body. Maskol is used to seal the body and the mdf box.

http://www.slotracinglemans.com/images/rfh/viper_mal03.jpg
Miliput rolled into a string is used to temporarely "glue" the master on the "bottom" of the box. This is absolutely nessecaryh because otherwise the master will start to "float" in the silicon.

http://www.slotracinglemans.com/images/rfh/viper_mal04.jpg
Depending on the dimensions of your master, the box should be ± 2cm oversized. If the box is too "tight" the walls of the silicon mold will become too thin too keep their proper shape. If the box is too big you need much more silicon...which is a waste of money!

http://www.slotracinglemans.com/images/rfh/viper_mal05.jpg
Care should be taken when you start pouring the silicon into the mold. Your main concerns will be to prevent air pockets. Pour slowly so the silicon can flow slowly around the master pushing away the air as the level rises.
Brushing the tricky areas like the headlamps and grille with silicon before pouring also helps to iliminate airpockets.
http://www.slotracinglemans.com/images/rfh/viper_mal06.jpg

And just as the roof goes under..... I ran out of silicon. Should this happen, no problem...just mix some more and continue pouring!
If you're completely out of silicon and the shops are closed!!! Just let the silicon set (takes ± 12- 16hrs)which should be more than enough time to buy some new. Mix the last part and then continue pouring on top of the hardened silicon!



Tamar
View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
HaCo





Posts:
Registered: 1-1-1970
Member Is Offline
posted on 2-1-2005 at 09:41 Reply With Quote


Tamar,

Ik kan niet wachten op het resultaat! :) Is het de bedoeling om in die mal uiteindelijk lexans te maken of een ander soort hard plastieken body?

Binnenkort kan je dus een klein viper fabriekske starten in A'dam!! :D

Ik hoop dat je snel weer nieuwe foto's post,

Groeten uit Belgie,
HaCo.
View User's Profile View All Posts By User U2U Member
VaCooL





Posts: 18
Registered: 20-6-2003
Member Is Offline
Mood: Porsche 911 GT1 '96
posted on 1-2-2005 at 10:58 Reply With Quote


when can we see the rest?
View User's Profile E-Mail User View All Posts By User U2U Member
willem
LMSadmin




Posts: 356
Registered: 5-11-1985
Location: Netherlands
Member Is Offline
Mood: Tired
posted on 1-2-2005 at 15:29 Reply With Quote
End result!



The endresult is already there! We've been driven this car a month ago in Leeuwarden. Check out the pics in the gallery.



View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
VaCooL





Posts: 18
Registered: 20-6-2003
Member Is Offline
Mood: Porsche 911 GT1 '96
posted on 10-2-2005 at 20:42 Reply With Quote


Yeah i know, I was where with Hernik from Denmark and the other guy's from here.

But i will like to se some pictures of how he was making the mold of the car,
How he put glasfiber in it or what els he uses.

Regards Jan
View User's Profile E-Mail User View All Posts By User U2U Member
Post new thread Poll:

Go To Top